· Industrial Utilities
Cooling a Hot Shop Floor: Ventilation, Evaporative Cooling or Air Conditioning?
How to choose between ventilation, evaporative cooling, spot cooling and air conditioning for a hot factory floor, and why cutting the heat load comes first.
In short
- Before choosing any cooling system, reduce the heat entering the shop: an insulated, reflective roof and extraction at hot sources often do more than added cooling.
- Mechanical ventilation removes heat but can never bring the shop below outdoor temperature.
- Evaporative cooling works well in dry heat, such as the Indian summer before the monsoon, and much less when the air is humid.
- Air conditioning is justified where a process needs controlled temperature or humidity, or for enclosed areas where people work for long periods.
- Spot cooling at workstations can make a hot shop workable at a fraction of the cost of cooling the whole volume.
A shop floor in summer can be several degrees hotter than the air outside it. The roof has been in the sun since morning, furnaces and ovens are running, motors, compressors and welding sets are all giving off heat, and the building has no way to get rid of it. Productivity drops, absenteeism rises, and some processes start to drift out of tolerance.
The usual first response is to buy more fans. Sometimes that is the right answer. Often it is not, and the choice between ventilation, evaporative cooling and air conditioning is worth making on purpose.
First, cut the heat coming in
Every cooling system is sized against the heat it has to remove. The cheapest unit of cooling is heat that never enters the space:
- The roof. On a single-storey factory the roof is usually the largest heat source. Insulation under the sheeting, or a reflective coating on top, can drop the inside surface temperature dramatically and with it the heat radiated onto people below.
- Hot processes. Furnaces, ovens, heat-treatment lines and die-casting machines should have their heat captured at source by hoods and extracted directly, not allowed to spread through the shop and then cooled.
- Equipment in the wrong room. Compressors, panels and transformers placed inside the production area add to its heat load. Moving them to a separately ventilated utility room removes it.
Only then is it worth sizing the cooling for what remains.
Option 1: Ventilation
Mechanical ventilation — roof extractors, wall-mounted exhaust fans and fresh air supply units — moves hot air out and outdoor air in. It is the lowest-cost option to install and to run.
Its limit is fundamental: ventilation can bring the shop close to the outdoor temperature, never below it. On a 38°C afternoon, a perfectly ventilated shop is still a 38°C shop. What ventilation does well is remove the extra heat that builds up above outdoor conditions, and that excess is often what makes a shop unbearable.
Ventilation should be designed from the heat load, with supply and exhaust arranged so air sweeps across the working zone rather than short-circuiting straight from inlet to outlet. Turbine ventilators on the roof help, but they move far less air than powered fans and cannot be relied on alone for a hot process shop.
Option 2: Evaporative cooling
Evaporative coolers and air washers pass outdoor air through wetted media. Water evaporates, absorbs heat, and the air leaves cooler and more humid. The air is then supplied to the shop, while an equal amount is exhausted.
How much it cools depends on how dry the outdoor air is — the gap between the dry-bulb and wet-bulb temperatures. A good cooler achieves most of that gap. An illustrative comparison:
| Conditions (illustrative) | Dry bulb | Wet bulb | Supply air at ~85% efficiency |
|---|---|---|---|
| Dry pre-monsoon afternoon | 38°C | 21°C | ≈ 23.5°C |
| Humid monsoon day | 30°C | 26°C | ≈ 26.5°C |
In the dry heat before the monsoon, evaporative cooling delivers a large drop at a small fraction of the running cost of air conditioning. In humid weather the drop shrinks and the added moisture makes the air feel heavier, so it relieves less. For many factories in western and central India, the hot months are the dry months, which is why evaporative cooling is so widely used.
It needs clean water, regular cleaning of media and tanks, and water treatment to keep scale and bacteria in check. It is not suitable where the process or the product cannot tolerate higher humidity.
Option 3: Spot cooling
Most of a factory's volume is air above people's heads. Spot coolers and man coolers deliver cooled or high-velocity air directly to fixed workstations — the operator at a furnace, a press or a welding bay — without trying to cool the whole building. Where people work at fixed points, spot cooling can make a hot shop workable for a fraction of the cost of cooling it all.
Option 4: Air conditioning
Full air conditioning — chilled water air handling units or packaged systems — controls temperature and, where required, humidity regardless of the weather. It is the most expensive to install and to run, and on a large, poorly insulated shop it can be very expensive indeed.
It earns its place where the process demands it:
- Precision machining, metrology and inspection, where temperature affects dimensions.
- Electronics, battery and pharmaceutical production, where humidity and cleanliness are controlled.
- Control rooms, panel rooms and enclosed offices on the shop floor.
Where only part of a plant needs it, enclosing that part and air-conditioning it alone is almost always cheaper than conditioning the whole building. The chilled water plant behind it is covered in industrial cooling tower selection.
Choosing between them
| Need | Usual answer |
|---|---|
| Shop much hotter than outdoors | Cut heat load, then ventilation |
| Hot, dry climate; people need relief | Evaporative cooling |
| People at fixed hot workstations | Spot cooling |
| Process needs controlled temperature or humidity | Air conditioning, for that area only |
Most hot shops end up with a combination: an insulated roof, extraction at hot sources, evaporative cooling for the general area, spot cooling at the hottest stations, and air conditioning only where the process requires it.
Questions buyers ask
How many air changes per hour does a hot shop need?
Air change rates are a useful check but a poor design basis. The ventilation should be sized from the heat it has to remove and the temperature rise the shop can accept; the air change rate falls out of that calculation.
Will evaporative cooling make the shop damp?
It raises humidity, which is the trade-off for its low running cost. With enough exhaust to carry the moist air out, and in the dry season when it is most needed, this is rarely a problem for people. It can be for moisture-sensitive products and electrical panels, which is why those areas are often kept separate.
What does a cooling retrofit involve in a running plant?
Roof insulation, exhaust fans and evaporative units can usually be installed in sections around production, with the main disruption at the points where ducts and units are lifted onto the roof.
How VPSTEC approaches it
Industrial ventilation and fresh air systems, chillers and air handling are part of VPSTEC's HVAC and cooling discipline, and heat-load reduction belongs to its energy efficiency work. Starting from the heat load, not from a cooling product, is what keeps the answer proportionate to the problem.
Related deliveries
